How To Program A Kwikset Smart Lock? Step-By-Step Guide!


How To Program A Kwikset Smart Lock

Kwikset Smart Locks are a great addition to home security. If you have already own a Kwikset Smart Lock, you probably wondering- how to program a Kwikset Smart Lock? Programming Kwikset Smart Lock is not a complicated process, all you need is to follow few step explained in this article to program the lock.

How to program a Kwikset Smart Lock? Press the programming button once on the backside of the lock. Enter your desired code and press the lock or Kwikset button. The lock will accept the program with the green flash and beeping response.

To know how to reprogram and manage a Kwikset Smart Lock properly, you must keep your eye on the article. Let’s head to it to get a concept thoroughly of Kwikset Smart Lock.

How To Reprogram A Kwikset Smart Lock?

You need to understand an important thing before reprogramming a Kwikset Smart Lock. Once you perform reprogramming, it will remove all the previous codes from memory. Following are the step-by-step process to reprogram a Kwikset Smart Lock:

  1. Put the bolt manually in the extended position.
  2. Press the program button a single time.
  3. Enter your new programming code that should be within 4 to 8 digits.
  4. Press the lock button.
  5. The program button two times.
  6. Enter a new code or the same code you have just entered.
  7. Again, press the lock button a single time.

This procedure should do the job. But if the old program code remains, we recommend performing the unit’s hard reset.

However, if you have a smart electronic deadbolt lock, read my recent article where I explain about step-by-step process of programming it.

How To Hard Reset Kwikset Smart Lock?

  1. Remove all the batteries.
  2. Keep the lock like this for one hour.
  3. Re-enter the batteries after one hour.
  4. Use the functioning key to turn ¼ turn clockwise.
  5. Insert your Smart-Key tool and then remove it.
  6. Remove the functioning key from the cylinder.
  7. Finally, insert a new key and turn ½ turn counter-clockwise.

You’ll be able to reprogram the Kwikset Smart Lock after the hard reset. If you had known how to program a kwikset smart lock before, these procedures might seem familiar to you. 

It is also essential to know when you need to reprogram your SmartLock. Security is a primary concern, and there can be various situations it becomes a must. We will let you know a few significant circumstances when you need to reprogram it.

Situation 1: Losing The Phone

If your phone has access to the lock and you lose your phone, there is a possibility of theft. Along with your other information, bad people might use it for their interest. Changing the program code isn’t a big deal. Consider reprogramming a must in such a situation.

Situation 2: Moving Into A New Home 

When moving into a new home, you should reprogram your lock to remove all the previous accessible codes. So, you can be sure to secure your home.

Situation 3: Lock Stops Functioning

Sometimes the lock stops functioning due to an internal jam. Reprogramming might fix the issue in such circumstances.

Situation 4: Suspicious Of Unauthorized Access

You must change the codes if you feel suspicious of unauthorized access. It may happen with the lock that has multiple codes.

How To Set A Kwikset Smart Lock Code?

Setting a Kwikset SmartLock code is relatively easy. You can change the lock many times. If you have never changed the code, you should. Why? Because you will leave your security vulnerable. All the Kwikset Smart Locks have the same default ‘0000’ setting. Anyone who would want to break into your house would try the default setting first. 

There are a few things to avoid while setting a Kwikset SmartLock code. Digits can vary with different models. If you choose four numbers, you must avoid easily guessed code. Consider it and avoid things like:

  • House number
  • Common patterns such as 1212
  • Birthdate
  • Phone number
  • Social security number
  • Commonly surmising numbers like 1234

We have discussed the part of the consideration before setting a  SmartLock code. Now we will talk about how you can do it.

Step 1: Turn the Lock Into Programming Mode

You can do this in two ways. Both of the ways below would do that. Keep your door unlocked. That will keep you from getting stuck outside.

  1. Enter the default programming code. Then press the Kwikset button one time. Right then, you will hear a single beep. The beep sound means that you can now program your code. 
  2. This method will allow you to turn the lock into programming mode when you don’t have a Kwikset button. You will find the programming button under the plastic dust cover. Press that button once, and you are all ready to go.

Step 2: Enter A New Code

We talked before that your code must be robust. So, put something unique. Enter the code you have decided on and press the lock button. Not every model has a lock button. Some may have a Kwikset button. It doesn’t matter if you have a Kwikset or lock button because they all perform the same in this matter. The lock will let you know by beeping twice when it accepts the code.

Even if all things go right, you must check the lock. Try locking and unlocking your door several times, keeping the door open. You can close the door when you are sure that your lock has accepted the code.

Step 3: Include Additional Users

A few Kwikset SmartLock models allow for more than one user. That means it can add multiple codes. So, how do you do that?

  1. While adding the first code, you had to press the programming button once. Press the programming button twice when adding the second lock. It works this way.
  2. Enter your preferred code and press the lock or Kwikset button.
  3. Every time you add a new code, you must check it until you are sure. Check it just like you did the first time.

How To Reset Kwikset Smart Lock?

How To Program A Kwikset Smart Lock

Resetting a Kwikset Smart Lock will erase all codes and memory and restore to the default factory settings. When your controller is inoperable, only then reset your Kwikset Smart Lock. You have to understand that resetting is not any regular program that you apply. So, know the reason why you are resetting and do reset. How do you do that?

  • Make sure you keep your door open while doing this.
  • Remove the battery pack.
  • Press the program button and re-insert the battery pack while holding the button.
  • Keep holding the button for around 30 seconds.
  • Leave the button when the status LED flashes red and hear a single beep.
  • Press the program button and hold.
  • Leave the button when the status LED flashes green and hear two beeps.

How To Remove Code From Kwikset Smart Lock?

As we know, you can have several codes in a single lock Kwikset Smart-Lock. However, you can remove a single or all the codes at once. Following are the step-by-step process of removing code from Kwikset smart lock:

  • Step 1: Keep the door open while you apply to the program.
  • Step 2: Allow the lock to run the program.
  • Step 3: Press 2 (the keypad will flash green, and you will hear a single beep).
  • Step 4: Press the Kwikset button.
  • Step 5: Enter the code you want to delete and press the Kwikset button.
  • Step 6: Again, enter the same user code.
  • Step 7: Press the Kwikset button.

You have successfully removed the code if you hear a long single beep and the keypad flashes green. And if the code removing process was unsuccessful, the keypad will flash red, and you will hear three beeps. You will have to repeat the steps carefully.

Remove All User Codes from Kwikset Smart Lock:

  1. Keep the door open while you apply to the program.
  2. Allow the lock to run the program.
  3. Press 4 (the keypad will flash green, and you will hear a short single beep).
  4. Press the Kwikset button.
  5. Press ‘9 – 9 – 9 – 9 – 9 – 9’.
  6. Press the Kwikset button.
  7. Press ‘9 – 9 – 9 – 9 – 9 – 9’ again.
  8. Press the Kwikset button.

You have successfully removed the code if you hear a long single beep and the keypad flashes green. And if the code removing process was unsuccessful, the keypad will flash red, and you will hear three beeps. You will have to repeat the steps carefully.

Perform this process at step 2: Press the programming button if you have never changed the preset programming code. Hold it until you hear two beeps. It should not take long. And if you have changed the programming code, enter your code and press the Kwikset button. When the keypad flashes green, and you hear a short beep, then it’s done.

Where Is The Program Button On A Kwikset Smart Lock?

The programming button is always in the back panel of the door lock. Kwikset SmartLock models have the programming button on the inside of the interior assembly. To reach the programming button, you might need to remove the interior cover. The button is often in the middle and easy to find out.

Very few models have the programming button visible. The visible buttons are at the edge of a little narrow hole. Sometimes you might need a straight wire to reach there.

How To Delete A User Code Using The Premis App?

Having a mobile app to manage Kwikset SmartLock is excellent. You can share your code through the app. All user codes will be visible in the app. If need be, you can delete all at once or one by one. Let’s follow the process to delete a single code with the app.

  1. Open the Premis App.
  2. Press on the lock icon.
  3. Click on the user icon. (There you would see two icons for the user. You will click on the lower left) side icon.
  4. Select the user name you wish to delete.
  5. Select ‘Delete User Code’(you will find it at the bottom edge of the interface).
  6. Click on delete to confirm the deletion.

How To Mute/Unmute Kwikset Smart Lock?

A muted lock might confuse you. When you command something to safety, it generally responds with beeping and status LED. If muted during system alerts, regular operation, or low battery indicators, you will not hear any beeping. To perform unmute, let’s head to it:

  1. Keep the door unlocked when you do this.
  2. Enter the Master code you have.
  3. Press the lock button (you will hear a single beep).
  4. Press 1-5 and the lock button again (If it were successful, it would make two beeps, and if not, it would make three beeps). 

How To Share An Access Code Using The Kwikset App?

The Kwikset app has made sharing codes safer and more accessible. If you have the app installed on your phone, follow the instructions.

  • Step 1: Go to the app’s main screen, tap on the access code icon in the bottom left corner. 
  • Step 2: Tap on the access code you want to share.
  • Step 3: Tap on the upload icon next to “Share Access Code.”
  • Step 4: Choose your preferred way to send the code, email WhatsApp, etc.
  • Step 5: You will get an automatically generated message with the Access Code and schedule information.

Did I Answer Everything You Want To Know About How To Program A Kwikset Smart Lock?

Kwikset Smart Locks are convenient as they function user-friendly. They allow managing the lock with their mobile app. Removing and adding codes has been easier since then. If you have read this article, you will not wonder how to program a kwikset smart lock, we hope. Our discussion on the necessary parts of Kwikset Smart Lock and how they function intend to build a better understanding with you.

Recent Posts